Quality control before every jacquard shipment

A fabric complaint rarely arrives as a surprise to the mill — it arrives as a surprise to the buyer. This page sets out what we check, how we check it, and what we will and will not claim about certification.

Inspection list

Six checks on every roll

The same list applies to every order, from a trial run to a repeat programme. Results are recorded roll by roll so a shipment can be traced back.

01

Usable width

Measured against the width stated on the order, not the nominal loom width. A shortfall here is what stalls a cutting plan, so it is checked first.

02

Weight (GSM)

Sampled across the roll against the ±5% tolerance agreed for the order. Drift between batches is the most common cause of repeat-order complaints.

03

Shade

Compared roll to roll and against the approved standard under consistent lighting. For repeat orders the original approved dip is kept on file as the reference.

04

Pattern alignment

Repeat size, alignment and weft density checked against the approved sample, particularly on stripe and geometric jacquards where drift is visible.

05

Surface and weaving defects

Inspected under light for broken picks, floats, stains, cut marks and uneven finishing.

06

Roll length and packing

Length verified, ends secured, rolls wrapped and marked to the buyer's instructions before loading.

Tolerances

The figures we hold ourselves to

Standard tolerances, confirmed per order
ParameterStandard toleranceNotes
Weight±5% of nominal GSMTighter windows quoted on request
Usable widthAs stated on order confirmationMeasured, not nominal loom width
ShadeAgainst approved standardReference dip kept for repeat orders
Roll lengthAs agreed per rollShortfalls credited, not absorbed
Pattern repeatAgainst approved sampleChecked on stripe and geometric jacquards

Any tolerance not stated here is agreed in writing on the order confirmation before production begins.

Jacquard fabric rolls inspected and stacked in the warehouse before packing in Changxing, Zhejiang
Inspected rolls waiting for packing and marking.

Honest limits

What we can and cannot promise

Buyers are rightly sceptical of mills that claim every certificate in the book. Our position is narrower and easier to verify.

  • We can arrange OEKO-TEX testing for the specific article and colour you order
  • We can supply third-party test reports for composition, GSM, width and colour fastness
  • We can welcome your nominated inspection agency before shipment
  • We can provide the Zhejiang Technology-Based SME registration as a company credential
  • We cannot describe standard production as OEKO-TEX certified when it has not been tested
  • We cannot guarantee colour matching against a screen image — only against a physical swatch

Colour and light

Shade approval is always against a physical standard under agreed lighting. A colour that looks correct on a monitor can differ by a full step in the dyed lot, which is why we ask for a swatch or Pantone number rather than a photograph.

Third-party inspection welcome

If your buyer or your own QA team wants to inspect before shipment, tell us the agency and the acceptance criteria at order stage so the schedule allows for it.

FAQ

Quality questions buyers ask

Do you inspect every roll or only sample rolls?

Every roll. Inspection is a fixed production step for us, not a spot check, because a defect found in the warehouse is far cheaper for both sides than one found at the cutting table.

What inspection standard do you follow?

We work to the width, GSM and shade tolerances stated on the order confirmation, checked under consistent inspection lighting. If you require a specific third-party standard such as a four-point system with a defined acceptance level, tell us at enquiry stage and we will confirm whether we can work to it.

Can I have a third-party inspection before shipment?

Yes. We welcome buyer-nominated inspection. Tell us the agency and the acceptance criteria and we will arrange access and timing so the inspection does not delay the sailing.

What happens if a defect is found after arrival?

Send photographs, roll numbers and the inspection record. Because inspection results are kept roll by roll, we can trace the batch, the loom and the finishing lot, then agree a remedy. Claims are handled on evidence rather than on assertion.

Can you provide test reports?

Yes, on request. Fibre composition, GSM, width and colour fastness can be tested by a third-party laboratory, and OEKO-TEX testing can be arranged for qualifying orders against the standard you specify. Test cost and lead time are quoted with the order.

Is your standard production OEKO-TEX certified?

No — and we prefer to be precise about this. OEKO-TEX certification is issued per tested article. We can arrange testing for the specific fabric and colour you order, and we will tell you exactly which standard applies once we know your target market.

Ask for the inspection record with your quotation

We can send the tolerance list and a sample inspection record with the offer, so you know exactly what will be checked before you place the order.

Chat on WhatsApp